» Introduced in 2004 «
Comfortable, Attractive, Coin Pattern Flooring |
 |
|
Gives your garage a showroom look |
|
Coin pattern flooring is offered in specially formulated,
heavy-duty, commercial & industrial grade material |
|
Click here to see how Coin Pattern Floor Covering
was used recently for an international tradeshow |
|
 |
|
 |
|
How does G-FLOOR®
Roll-Out Garage Flooring compare with other vinyl floor coverings?
BLT G-Floor is 100% high quality polyvinyl throughout the entire product. Most other floor coverings
only use high quality materials on the top 10%–20% of their product and laminate with lower-grade material
that does not offer the same protection throughout. Some products even have three layers of filler using
some of the poorest quality materials available.
G-Floor is solid polyvinyl and has the same resistances throughout the entire product top to bottom.
G-Floor is superior to all other floor coverings that you can drive and walk on. |
|
|
Ron Hazelton's HouseCalls® show |
|
|
|
|
|
Other G-FLOOR® appearances on
Ron Hazelton's HouseCalls® show |
|
|
|
 |
 |
|
CAUTION—SAFETY WARNING:
Any floor surface can become slippery in the presence of moisture and debris.
Proper care and cleaning of vinyl flooring will reduce the likelihood of slips and falls.
Wipe up any oil, chemicals, or other fluids that may drip or leak from vehicle to prevent
hazardous, slippery conditions. Always dispose of hazardous materials properly. |
|
IS G-Floor® A SLIP-RESISTANT FLOORING PRODUCT?
Although the patterned design of BLT flooring offers somewhat improved traction compared
to bare concrete, BLT makes no claim of G-Floor being slip-proof or slip-resistant.
There is no substitute for keeping a clean, well-maintained floor. |
|
|
|
 |
|
Coin Pattern Floor Covering is produced and
stocked in the following widths & lengths
Commercial Grade G-FLOOR® 75 Coin Pattern
75 mil (0.075"—1.9 mm) Base thickness
115 mil (0.115"—2.9 mm) Overall flooring height
is produced in 3 stock sizes:
• 7.5' wide x 17' length
• 8' wide x 22' length
• 10' wide x 24' length
(75 mil base thickness is between a quarter & a nickel)
Industrial Grade G-FLOOR® 85 Coin Pattern
85 mil (0.085"—2.16 mm) Base thickness
125 mil (0.125"—3.2 mm) Overall flooring height
is produced in 2 stock sizes:
• 9' wide x 44' length
• 9' wide x 60' length
(85 mil base thickness is a bit thicker than a nickel)
|
 |
Coin Pattern flooring is ONLY available
in WIDTHS of 7.5', 8', 9', or 10'
Still a bit confused over "width" and "length"?
Click here for more explanation |
BLT Floor Covering of custom LENGTH is available
with additional charges and longer lead times.
To get a quote from Elite Xpressions on
custom size garage flooring
click here
To get a quote from garagefloor.com.com (a JNK Products website)
on custom size garage flooring
click here
Custom size garage flooring available from
American Garage Floor » click here |
|
 |
Alfa Romeo photos courtesy of Vintage Racecar magazine
G-Floor Coin Pattern flooring in Sandstone color provided by BLT |
 |
|
 |
|
G-Floor Coin Flooring available in six attractive colors |
COLOR NOTE: Due to the nature of process manufacturing,
flooring purchased on different days may not be identical in color.
COLOR NOTE: Industrial Grade Coin Flooring is
currently stocked in Slate Grey and Midnight Black ONLY |
|
Easy Installation of Roll-Out Garage Flooring
30 to 60 minutes
Minimal tools!—No adhesives required! |
|
 |
 |
 |
 |
|
Simply unroll |
Trim and overlap if needed |
Taping is optional* |
|
*3-M® brand 80 Rubber & Vinyl Spray Adhesive may also be used if desired. |
|
|
Step-by-Step Installation Instructions |
1)
For best result, unpack and install product as soon as possible after delivery. The sooner product is removed from
packaging, the sooner it will lay flat on garage floor after installation.
2)
Sweep and clean garage floor. Wipe up any oil and chemicals from floor before rolling out product.
3)
Unroll product on garage floor. Edges may be butted together or overlapped (see Overlap Note below) for seamless appearance and floor protection. Initially,
the Garage Floor Protector will have curl marks due to being rolled on a core or folded in a box for shipment (this is normal).
Unroll option 1:
For lay flat results, unroll Garage Floor Protector in the sunlight on a clean driveway. The warmer the conditions
the quicker curls will straighten out and lay flat. Use wide push broom, push air out from center and work your way out
(side to side and length to length) Repeat if necessary. Place on garage floor when desired and repeat broom out.
Unroll option 2:
If you wish to unroll product directly on the garage floor, sweep garage floor clean of debris and unroll Garage Floor Protector.
For best results, start unrolling process at the garage entrance; finishing at the back of the garage. Note: In cool to
cold conditions it may take 72+ hours for most curl marks to lay flat depending on the temperature. Be sure to push out air with
broom (It is OK to park your car on it during this time). |
|
Overlap note:
G-Floor® Flooring that is 10'
wide, has an "overlap flap"
(approximately 1.5" to 2" wide)
of unpatterned material
running down one side.
Flooring that is 9' wide or less,
has no "overlap flap". |
 |
|
4)
Allow mat to relax and lay flat. For custom fit, allow product to relax in place before trimming around edges and corners.
Note: If product is used under extreme temperature conditions, such as direct sunlight or unheated garages, the product may expand or contract as much as 2% after laying flat. For custom fit, always allow product to relax before trimming around edges and corners.
5)
Trim edges with sharp scissors or utility knife.
6)
Taping around edges is not necessary. This product can expand or contract up to 2% with temperature changes. It is best if the product is allowed to 'float' freely on the floor. If you choose to tape the seam between two floor protectors, we recommend using indoor-outdoor carpet tape.
Note: Due to the manufacturing process, patterns of two pieces of flooring may not match or align exactly along the seam when two mats are laid side by side.
|
For specific questions regarding:
product installation, care, or cleaning,
please contact
Customer Service at Better Life Technology |
|
NOTE:
The Accessories Group, a distributor of G-FLOOR™ Roll-Out Garage Flooring,
recently created a set of professional installer guidelines. For wall-to-wall professional installation instructions,
click the tag logo below.
|
|
|
|
|
Product Cleaning and Care
of BLT Roll-Out Garage Flooring |
|
|
•
Surface is easily washed with soap and water. Product can be easily washed off inside or outside of garage. Brush or sweep with
cool water using a broom or sponge squeegee. Mild soaps and normal household detergents may be used. Do not leave harsh
detergents or chemicals on product or wash into sewer system. Some people prefer moving the product outside and hosing it off.
•
Normal household vinyl cleaners may be used to increase longevity and to remove stubborn debris. Certain automotive vinyl
products may cause surface to become slippery. Use a non-slip vinyl protector such as a clean-and-shine floor cleaner.
•
This is not a stain-proof product—certain dyes, inks, rubber tires, and chemicals may cause permanent staining.
Some of our customers have reported that spray-on Brake and Tool Cleaner, found in many auto parts stores,
will remove some stubborn stains without damaging the product. However, use of brake and tool cleaner may
cause product discoloration. Never use harsh chemicals such as tar remover or kerosene on this product.
•
After cleaning, apply a coat of floor polish for vinyl floors to add a long-lasting, high-luster finish, even to older garage floor protectors.
NOTE:
Leaving chemicals on the product for a long period of time may cause damage. If concrete floor has been treated
with certain sealers prior to mat installation, sealer may break down over time and adhere to back of mat without
causing damage to mat. Some motorcycle kickstands may cut or damage this product. |
|
CAUTION—SAFETY WARNING:
Any floor surface can become slippery in the presence of moisture and debris.
Proper care and cleaning of vinyl flooring will reduce the likelihood of slips and falls.
Wipe up any oil, chemicals, or other fluids that may drip or leak from vehicle to prevent
hazardous, slippery conditions. Always dispose of hazardous materials properly. |
|
IS G-Floor® A SLIP-RESISTANT FLOORING PRODUCT?
Although the patterned design of BLT flooring offers somewhat improved traction compared
to bare concrete, BLT makes no claim of G-Floor being slip-proof or slip-resistant.
There is no substitute for keeping a clean, well-maintained floor. |
|
For specific questions regarding:
product installation, care, or cleaning,
please contact
Customer Service at Better Life Technology |
|
