Better Life Technology, LLC
Roll-Out Garage and Concrete Floor Covers
• World's Largest Producer of Garage Floor Protector Mats
• Producer of the World's Widest Roll-Out Garage Floor Covering
» By Popular Demand «
Diamond Tread Pattern Flooring
Now Available
Diamond Tread Flooring in Metallic Silver color
Available soon in these sizes: 7.5 ft x 17 ft,
10 ft x 24 ft, 9 ft x 60 ft
Metallic Silver flooring is now available from California Car Cover Company
Diamond Tread pattern flooring is offered in specially formulated,
heavy-duty, commercial and industrial grade material
G-FLOOR®
Diamond Tread is preferred by many auto enthusists.
It has the most 'macho' look and matches some popular garage storage cabinets.
This pattern also provides improved traction over bare floors.
How does G-FLOOR®
Roll-Out Garage Flooring compare with other vinyl floor coverings?
BLT G-Floor is 100% high quality polyvinyl throughout the entire product. Most other floor coverings only use high quality materials on the top 10%–20% of their product and laminate with lower-grade material that does not offer the same protection throughout. Some products even have three layers of filler using some of the poorest quality materials available.
G-Floor is solid polyvinyl and has the same resistances throughout the entire product top to bottom.
G-Floor is superior to all other floor coverings that you can drive or walk on.
CAUTION—SAFETY WARNING: Any floor surface can become slippery in the presence of moisture and debris.
Proper care and cleaning of vinyl flooring will reduce the likelihood of slips and falls.
Wipe up any oil, chemicals, or other fluids that may drip or leak from vehicle to prevent
hazardous, slippery conditions. Always dispose of hazardous materials properly.
IS G-Floor® A SLIP-RESISTANT FLOORING PRODUCT?
Although the patterned design of BLT flooring offers somewhat improved traction compared
to bare concrete, BLT makes no claim of G-Floor being slip-proof or slip-resistant. There is no substitute for keeping a clean, well-maintained floor.
Diamond Tread Floor Covering is produced &
stocked in the following widths & lengths
Commercial Grade G-FLOOR® 75 Diamond Tread Pattern
75 mil (0.075"—1.9 mm) Base thickness
130 mil (0.130"—3.3 mm) Overall flooring height
is produced in 3 stock sizes:
• 7.5' wide x 17' length
• 9' wide x 20' length
• 10' wide x 24' length
(75 mil base thickness is between a quarter & a nickel)
Industrial Grade G-FLOOR® 85 Diamond Tread Pattern
85 mil (0.085"—2.16 mm) Base thickness
140 mil (0.140"—3.56 mm) Overall flooring height
is produced in 2 stock sizes:
• 9' wide x 44' length
• 9' wide x 60' length
(85 mil base thickness is a bit thicker than a nickel)
Diamond Tread flooring is only produced &
stocked in WIDTHS of 7.5', 9', or 10'
8' width is also available by special order
Minimum quantity and longer lead time will be required
Still a bit confused over "width" and "length"? Click here for more explanation
BLT Floor Covering of custom LENGTH is available
with additional charges and longer lead times.
Custom size garage flooring available from
American Garage Floor » click here
To get a quote from garagefloor.com.com (a JNK Products website) on custom size garage flooring
click here
To get a quote from Elite Xpressions on custom size garage flooring
click here
COLOR NOTE:
Diamond Tread Pattern Flooring is now stocked in Midnight Black,
Slate Grey, and Metallic Silver » »
Note: Due to the nature of process manufacturing,
flooring purchased on different days may not be identical in color.
Easy Installation of Roll-Out Garage Flooring 30 to 60 minutes
Minimal tools!—No adhesives required!
Simply unroll
Trim and overlap if needed
Taping is optional*
*3-M® brand 80 Rubber & Vinyl Spray Adhesive may also be used if desired.
Step-by-Step Installation Instructions
1)
For best result, unpack and install product as soon as possible after delivery. The sooner product is removed from
packaging, the sooner it will lay flat on garage floor after installation.
2)
Sweep and clean garage floor. Wipe up any oil and chemicals from floor before rolling out product.
3)
Unroll product on garage floor. Edges may be butted together or overlapped (see Overlap Note below) for seamless appearance and floor protection. Initially,
the Garage Floor Protector will have curl marks due to being rolled on a core or folded in a box for shipment (this is normal).
Unroll option 1:
For lay flat results, unroll Garage Floor Protector in the sunlight on a clean driveway. The warmer the conditions
the quicker curls will straighten out and lay flat. Use wide push broom, push air out from center and work your way out
(side to side and length to length) Repeat if necessary. Place on garage floor when desired and repeat broom out.
Unroll option 2:
If you wish to unroll product directly on the garage floor, sweep garage floor clean of debris and unroll Garage Floor Protector.
For best results, start unrolling process at the garage entrance; finishing at the back of the garage. Note: In cool to
cold conditions it may take 72+ hours for most curl marks to lay flat depending on the temperature. Be sure to push out air with
broom (It is OK to park your car on it during this time).
Overlap note:
G-Floor® Flooring that is 10' wide, has an "overlap flap"
(approximately 1.5" to 2" wide) of unpatterned material running down one side.
Flooring that is 9' wide or less, has no "overlap flap".
4)
Allow mat to relax and lay flat. For custom fit, allow product to relax in place before trimming around edges and corners.
Note: If product is used under extreme temperature conditions, such as direct sunlight or unheated garages, the product may expand or contract as much as 2% after laying flat. For custom fit, always allow product to relax before trimming around edges and corners.
5)
Trim edges with sharp scissors or utility knife.
6)
Taping around edges is not necessary. This product can expand or contract up to 2% with temperature changes. It is best if the product is allowed to 'float' freely on the floor. If you choose to tape the seam between two floor protectors, we recommend using indoor-outdoor carpet tape.
Note: Due to the manufacturing process, patterns of two pieces of flooring may not match or align exactly along the seam when two mats are laid side by side.
NOTE:
The Accessories Group, a distributor of G-FLOOR™ Roll-Out Garage Flooring,
recently created a set of professional installer guidelines. For wall-to-wall professional installation instructions,
click the tag logo below.
Product Cleaning and Care of BLT Roll-Out Garage Flooring
•
Surface is easily washed with soap and water. Product can be easily washed off inside or outside of garage. Brush or sweep with
cool water using a broom or sponge squeegee. Mild soaps and normal household detergents may be used. Do not leave harsh
detergents or chemicals on product or wash into sewer system. Some people prefer moving the product outside and hosing it off.
•
Normal household vinyl cleaners may be used to increase longevity and to remove stubborn debris. Certain automotive vinyl
products may cause surface to become slippery. Use a non-slip vinyl protector such as a clean-and-shine floor cleaner.
•
This is not a stain-proof product—certain dyes, inks, rubber tires, and chemicals may cause permanent staining.
Some of our customers have reported that spray-on Brake and Tool Cleaner, found in many auto parts stores,
will remove some stubborn stains without damaging the product. However, use of brake and tool cleaner may
cause product discoloration. Never use harsh chemicals such as tar remover or kerosene on this product.
•
After cleaning, apply a coat of floor polish for vinyl floors to add a long-lasting, high-luster finish, even to older garage floor protectors.
NOTE:
Leaving chemicals on the product for a long period of time may cause damage. If concrete floor has been treated
with certain sealers prior to mat installation, sealer may break down over time and adhere to back of mat without
causing damage to mat. Some motorcycle kickstands may cut or damage this product.
CAUTION—SAFETY WARNING: Any floor surface can become slippery in the presence of moisture and debris.
Proper care and cleaning of vinyl flooring will reduce the likelihood of slips and falls.
Wipe up any oil, chemicals, or other fluids that may drip or leak from vehicle to prevent
hazardous, slippery conditions. Always dispose of hazardous materials properly.
IS G-Floor® A SLIP-RESISTANT FLOORING PRODUCT?
Although the patterned design of BLT flooring offers somewhat improved traction compared
to bare concrete, BLT makes no claim of G-Floor being slip-proof or slip-resistant. There is no substitute for keeping a clean, well-maintained floor.
All photos, text, and other materials used on this website are the property of
Better Life Technology, LLC and may not be used without written permission.
NOTE:
The Parking Pad and G-FLOOR logos and names are registered trademarks of Better Life Technology, LLC.
ALSO, The phrase "BLT Roll-Out Garage Flooring" is a registered trademark of Better Life Technology, LLC.
In Addition, the X-treme Protection and X-treme Garage logos
are trademarks of Better Life Technology, LLC.
